Do you want to make a mini solar panel at your home for generating electricity? First, you must know the technique you must follow to prepare it successfully. Panels of solar make use of silicon-coated glass cells to capture the sunlight correctly.
The silicon-coated glass cells capture the sunlight and produce electricity. However, you need to follow specific steps to make the mini solar panels at your home. Therefore, you need to be careful while making mini solar panels at your home.
You have to follow specific steps to get things done in the correct order. You have to make your choices in the right direction to get things done in the correct order.
How To Make Mini Solar Panel At Home?
You need to take care of several factors while preparing the solar panels at your end. Do not make a mistake in this regard; otherwise, the entire process and hard work will go in vain. You have to know the steps for preparing the mini solar panels at home.
1. Mix Alcohol With Titanium Dioxide Powder Along With DishSoap To Form Paste
You have to combine alcohol with 0.5 grams of nanopowder for forming a mixture that is as thick as toothpaste. Then, you have to use the high-proof spirit like 40 proof of vodka or the particles of grain alcohol. Finally, you have to mix and paste the clear dish soap to stick to the conductive glass.
For crystallizing the titanium dioxide high, proof alcohol is required to absorb solar energy. The electrons present in the Crystallized Titanium get excited when sunlight falls on it, generating electricity.
Read More: Solar Panel Maintenance Requirements: What You Need To Know
2. Apply Even Layer Of Titanium Paste On Square Conductive Glass
You have to apply the transparent tape on a 10 by 10cm on the square of the conductive glass. The Tape must run about 3 mm starting from the edge of each side.
Then, you have to Titanium paste can be applied with the help of an eyedropper and spread uniformly over the edges using a blunt knife.
The tape present in the glass will help you control the titanium paste to spread over the surface. The second step is for conducting the electricity, you need to have a conductive glass with you.
After that, you have to apply the titanium paste on the side of this conductive glass. If you do not know which side is the conductive side, you can use the multimeter to measure the sides that show 20-30ohms of current is your conductive side.
3. For 10-20 Minute Heat The Glass On A Hot Plate
The third step is to remove the tape after coating the glass. Then, finally, you have to place the square on the hot plate and switch on the oven at a high temperature unless the coating turns brown and, lastly, white again.
You have to continue the process for about 10-20 minutes. Then, when the paste is white again, you have to turn off the burner and let the paste cool for at least 20-30 minutes.
You can also heat the mixture on an electric burner if you do not have a hot plate. Again, prepare the mix in the right proportion. It will help you to conduct the electricity from the plate.
4. In Strong Hibiscus Tea Soak The Cool Glass
Once the square is cool, you have to immerse it in the strong hibiscus tea for 2-3 hours. After 2-3 hours, the titanium coating will turn deep purple. Another way you can also n soak it in the thawed form for at least 3 hours.
The dying and the coating will enable to absorption of visible light. Now, if you leave the coating in white, it will only absorb the UV rays, but it cannot generate any form of currency.
You have to know the tricks that can help you prepare the mini solar panel in your home. You have to make things possible in the correct order.
5. Use Graphite Pencil To Color The Center Of Second Glass
You can use the graphite pencil and color the center of the square, which will help you conduct the electricity from the solar panel. You can make the holding of the center of the square to make the color flame.
The pencil’s graphite will help you conduct the electricity from the mini solar panel. First, of course, you have to wipe out any soot from the edges of the plane to make things work for you in all possible manners.
The cell will not generate any current form unless you make the graphite soot for countering the electrode.
6. Titanium Square Must Be Covered With Tape
You have to use the Titanium tape that is spread around the 3mm around the edges of the square with the help of the Titanium coating. The tape will act as a spacer between the two glass squares.
You need to fold the tape around the edges instead of folding it on the surface. It will make the process of the preparation of mini solar panel easier for you.
Continue Read About: Solar Panel Kits: A Complete Overview
7. Add Some Drop Of Electrolyte Solution On Center Of Titanium Square
The alcohol and the Lugol solution are capable enough to create the electrolyte, which will help you conduct the electricity from the solar panels.
Electrolyte solutions transfer the electrons and create the electricity to pass through the panels of the Titanium square when the drop of it falls on the surface of the electrolyte solution. You must not make things more complicated for yourself.
Final Take Away
Hence, you have to follow the above procedures to create mini solar panels in your home. Do not skip the process, as every step is crucial in adequately functioning the solar panel adequately. You can also share your tips about this matter for preparing the perfect solar panel for your home.
The DIY method will work well in your favor when you apply the process in the correct order at the right point in time. You have to follow the process in the proper way to make things work for you.
Read Also:
Tags:
Arnab Das is a passionate blogger who loves to write on different niches like technologies, dating, finance, fashion, travel, and much more.
